Rugao Lian Tuo Electronics Co.,Ltd
+8613862730866
Michael Chen
Michael Chen
Lead Engineer in the R&D department, focusing on cutting-edge semiconductor solutions. Always curious about pushing technological boundaries.
Contact Us

How to solder 1N5819 properly?

Oct 21, 2025

Hey there! As a supplier of 1N5819 diodes, I've seen firsthand how important it is to solder these components properly. In this blog, I'll walk you through the steps to solder 1N5819 diodes like a pro.

What is 1N5819?

First off, let's talk a bit about what 1N5819 is. The 1N5819 is a Schottky diode. Schottky diodes are known for their low forward voltage drop and fast switching speeds, which makes them great for applications like power supplies, voltage clamping, and high - frequency circuits. You can find more detailed info about 1N5819 on our website 1N5819.

Tools and Materials You'll Need

Before you start soldering, you'll need to gather a few essential tools and materials:

  • Soldering Iron: A good quality soldering iron with adjustable temperature is a must. I recommend setting the temperature between 350 - 400°C for soldering 1N5819.
  • Solder: Use lead - free solder with a diameter of around 0.6 - 0.8mm. It's important to choose a solder that has good wetting properties.
  • Flux: Flux helps to clean the surfaces and improve the flow of solder. You can use liquid flux or flux - core solder.
  • Soldering Stand: This keeps your hot soldering iron safely in place when you're not using it.
  • Wire Cutters and Strippers: You'll need these to trim the leads of the 1N5819 and prepare the wires for soldering.
  • Magnifying Glass: A magnifying glass can be really helpful, especially if you're working on a small circuit board. It allows you to see the soldering joints clearly.

Preparing the Workspace

A clean and organized workspace is key to successful soldering. Make sure your workbench is free of clutter and debris. Place your soldering stand within easy reach so you can safely rest the soldering iron when you need to. Also, make sure you have good ventilation, as soldering can produce fumes that are not good for your health.

Preparing the 1N5819 Diode

The 1N5819 has two leads: the anode and the cathode. The cathode is usually marked with a stripe on the body of the diode. Before soldering, you'll need to trim the leads to the appropriate length. Use your wire cutters to cut the leads so that they are about 2 - 3mm longer than the holes on the circuit board.

Soldering the 1N5819

Now, let's get to the actual soldering process. Here are the steps:

SR51003

  1. Tinning the Soldering Iron Tip: Before you start soldering, it's important to tin the tip of your soldering iron. Heat up the soldering iron to the appropriate temperature, then touch the tip of the iron to the solder. A small amount of solder should melt and coat the tip. This helps to transfer heat more efficiently.
  2. Applying Flux: If you're using liquid flux, apply a small amount to the holes on the circuit board where you'll be soldering the 1N5819. If you're using flux - core solder, this step is not necessary as the flux is already in the solder.
  3. Inserting the Diode: Carefully insert the 1N5819 into the holes on the circuit board, making sure the anode and cathode are in the correct positions. You can double - check the markings on the diode and the circuit board to ensure proper orientation.
  4. Soldering the Leads: Once the diode is in place, heat the lead of the diode and the pad on the circuit board simultaneously with the soldering iron. Hold the iron in place for about 2 - 3 seconds to allow the heat to transfer. Then, touch the solder to the joint. The solder should melt and flow around the lead and the pad, creating a smooth, shiny joint. Make sure not to apply too much solder, as this can cause shorts.
  5. Inspecting the Joint: After soldering each lead, inspect the joint closely. A good soldering joint should be smooth, shiny, and have a concave shape. If the joint looks dull, grainy, or has a ball of solder on it, it may be a cold joint. In this case, you'll need to re - heat the joint and add a little more solder if necessary.
  6. Trimming the Leads: Once you're satisfied with the soldering joints, use your wire cutters to trim the excess leads close to the surface of the circuit board.

Troubleshooting

Sometimes, things don't go as planned when soldering. Here are some common problems and how to fix them:

  • Cold Joints: As mentioned earlier, cold joints look dull and grainy. This is usually caused by insufficient heat or not enough solder. To fix a cold joint, re - heat the joint with the soldering iron and add a little more solder.
  • Shorts: Shorts occur when there is an unwanted connection between two or more components or pads on the circuit board. This can be caused by too much solder or solder bridging between two adjacent pads. To fix a short, you can use a desoldering pump or desoldering braid to remove the excess solder.
  • Lifted Pads: If you apply too much heat or pressure when soldering, you may lift a pad off the circuit board. This can be a serious problem, but in some cases, you can try to re - attach the pad using a small amount of conductive epoxy.

Other Schottky Diodes

The 1N5819 is just one type of Schottky diode. There are other popular ones like SS14 and SR5100. The SS14 is a surface - mount Schottky diode with a lower current rating compared to the 1N5819, while the SR5100 is a high - current Schottky diode suitable for power - hungry applications.

Conclusion

Soldering 1N5819 diodes properly is not as difficult as it may seem. By following the steps outlined in this blog and using the right tools and materials, you can create reliable soldering joints. Remember to take your time, work in a clean and well - ventilated workspace, and inspect your soldering joints carefully.

If you're interested in purchasing 1N5819 diodes or other Schottky diodes, feel free to reach out to us for a quote and to start a procurement discussion. We're here to help you with all your diode needs!

References

  • "Practical Electronics for Inventors" by Paul Scherz and Simon Monk.
  • "Getting Started in Electronics" by Forrest M. Mims III.